Final Bill Inzunza.pdf

Analyzed April 21, 2026

Overall Score

80%

Total Items

45

Passed

36

Failed

7

Warnings

2

Executive Summary

The estimate for repairs on the 2021 Porsche Macan AWD is broadly comprehensive, with most major operations and components listed for the areas repaired, including bumper, hood, fender, and refinish. There is strong compliance in core line items such as major R&I, paint/refinish, most necessary scans/calibration, and essential sublet/material elements. However, several industry-standard guide items are absent or appear underrepresented, especially for required prep, protective, and specialized material operations. Notable gaps include missing weld-through primer, cavity wax, proper labor units for certain procedures, and required protection/wrap for R&I items. Additionally, paint/repaint operations are light on specific prep and masking labor/material entries. These should be addressed for full guide compliance. The inclusion of ADAS scanning and hazardous waste is appropriate, but there are a few material undercharges. Recommendations are to update the estimate to add required protection, weld, and material operations, as well as to bring any labor below-guide up to minimums.

01 - Bumper

Warning

Core bumper R&I, repair, and refinish operations are present, but some required minor prep and protection items are missing or unspecified.

R&I Bumper Cover— Operation listed (line 10).
Req: Required for bumper repairEst: Included
Repair Bumper Cover— Operation listed (line 11).
Req: Required for bumper repairEst: Included
Refinish OEM 'Raw' Bumper/2nd Color/Black-out— Refinish including clear and base listed (lines 12, 13). Black-out is not itemized but base and clear are present.
Req: At least 1.4 labor units (& 1.0 for second color if applicable)Est: Total refinish labor is reasonable
Flex Additive— Listed (line 66).
Req: Required for flexible bumper refinishingEst: Included
Wrap-Store and Protect R&I Items— Not present; should be included to protect parts during repair per guide.
Req: 3.00 material, 0.2 labor minEst: Missing
Mask Unpainted Areas on Bumper— 'Mask openings' appears (line 72), but specific masking of unpainted/two-tone/fog areas is not itemized.
Req: 1.5 labor unitsEst: Unclear, likely missing

Missing Line Items

Wrap-Store and Protect R&I Items
Mask Unpainted Areas on Bumper

05 - Hood

Fail

Major hood R&R operations included, but several required prep, seal, and protection operations are missing. Several minimum labor units are not explicitly met.

Remove/Replace Hood— Listed (line 32, 169.0 labor units).
Req: RequiredEst: Included
Hood Insulation, R&I— Not present; no insulation or insulation retainer ops found.
Req: Seam seal, edges, and insulation r&i often required for aluminum hood per guideEst: Missing
Seam Seal Inner Edge of New Hood (if new/alum.)— Not present, required for new/aluminum hood.
Req: 1.0 labor, 121.06 materialEst: Missing
Mask Hood Inner Edges— Not included; not explicitly listed.
Req: 0.3 laborEst: Missing
Refinish Stand Set Up (Hood)— Not included.
Req: 0.3 laborEst: Missing

Missing Line Items

Hood Insulation, R&I
Seam Seal Inner Edge of New Hood
Mask Hood Inner Edges
Refinish Stand Set Up for Hood

10 - Fender

Warning

Blend operations for fenders included, but no liner/moldings/fender prep/protection operations shown.

Blend Lower Panel (ALU)— Listed (lines 40, 41).
Req: Required for adjacent blendEst: Included
R&I Fender Liner (if fender or adjacent repair)— Not listed. If lower repairs or blends performed, liner should be protected or removed.
Req: 0.8 laborEst: Missing
Mask Fender Jams & Openings— Not listed.
Req: 0.4 laborEst: Missing

Missing Line Items

R&I Fender Liner
Mask Fender Jams & Openings

15 - Coresupport

Warning

Core support ducting and bracket work performed but missing prep and typical post-repair protection items.

Remove/Replace Front Duct— Present (line 28).
Req: RequiredEst: Included
Test Fit Parts Attaching to Coresupport— No test fit or access time itemized.
Req: 1.0 laborEst: Missing

Missing Line Items

Test Fit Parts Attached to Coresupport

110 - Paint Prep

Warning

Some additional prep and blocking is included, but items for paint film measurement, protection, and hazardous waste are inconsistently listed or missing.

Block Sand and Fill— Listed (line 68).
Req: Required for repaired panelsEst: Included
Hazardous Waste Disposal— Included (line 67), adequate.
Req: Must be presentEst: Included
PAINT FILM MIL THICKNESS MEASUREMENT— Not listed anywhere.
Req: Required for panels blended/repairedEst: Missing
Wrap/Protect R&I Items— Not itemized in refinish section.
Req: Required as protection during refinish/prepEst: Missing

Missing Line Items

Paint Film Mil Thickness Measurement
Wrap-Store and Protect R&I Items

115 - Refinish Process

Warning

Color tint included, as is masking for primer. But no 'cover car' (beyond a generic note) is clear. Jamb/edge masking and some spot paint items missing.

Color Tint & Test— Listed (line 69).
Req: 2.0 labor min for difficult color/3-stageEst: Included
Mask for Priming— Listed as 'Additional Cover Car (Mask for Prime)' (line 70).
Req: 1.5 laborEst: Included
Cover Vehicle (Refinishing)— Listed generically as 'Cover Car' but not adequately detailed or with proper labor/materials.
Req: 1.0 labor, specific materialEst: Unclear/noncompliant

Missing Line Items

Cover Vehicle (for Refinishing)

180 - ADAS Functionality

Pass

Pre- and post-scan, static calibration (for park sensors, highly relevant to bumper/grille/ADAS), and mechanical labor presented and appropriate.

Pre-repair Scan— Listed (line 59).
Req: 65.00 (guide), at least one scanEst: Included, $57.50
Post-repair Scan— Listed (line 60), plus static calibration (line 61).
Req: 65.00 each + static or dynamic calibration if ADAS presentEst: Included