Estimate_to_Repair.pdf

Analyzed April 8, 2026

Overall Score

58%

Total Items

44

Passed

20

Failed

18

Warnings

6

Executive Summary

This is a comprehensive multi-section estimate for a 2017 Mercedes-Benz E-Class involving heavy front structural, exterior panel, lamp, restraint system, and interior trim repairs. Several key required line items from the 2025 Estimating Guide are missing in frame/unibody, welded/jointed repairs, and in protection and paint prep steps. While the majority of overt panel R&I/R&R operations and ADAS scan basics are present, the estimate consistently omits industry-required items such as weld-through primer, cavity wax, masking for primer, and wrap/store operations. The use of some correct overlap deductions is noted, but critical structural integrity and corrosion protection operations have been omitted throughout the major repair sections. Labor times are mostly at or above guide minimums, except where critical sub-operations are missing entirely. Material prices are rarely itemized for areas where the guide explicitly requires them. Overall, this estimate covers the superficial repairs but misses many internal or hidden procedures and protections that are essential for quality and compliance—including paint, welding, and structural best practices. Corrections are recommended before claim submission to avoid supplement delays and ensure appropriate reimbursement and repair quality.

01 - Bumper/Grille

Warning

Primary R&R items present; missing protection, prep, and some material/sublet details.

Overhaul bumper assemblyOperation present with correct labor units (4.2); R&R also included.
Req: 4.2 (overhaul)Est: 4.2
Add for Clear CoatIncluded for related painted components.
Req: As needed per paint opsEst: 1.1, 0.1
R&I/R&R SensorsLine items state 'Park sensor outer' but the labor time is below guide min (should be per sensor).
Req: 0.5 per sensorEst: 0.2 (total)
AIM FOG LAMPSNo line for aiming fog lamps; estimate only has 'aim headlamps'.
Req: 0.6Est: missing
Wrap-store and protect R&I itemsNo evidence of wrap/store/protect for removed sensor/brackets and bumper.
Req: $3.00, 0.2Est: missing
Flexible parts adhesion promoterPresent as stand-alone line.
Req: 0.7Est: included

Missing Line Items

AIM FOG LAMPS
Wrap-store and protect R&I items
TRIAL FIT BUMPER
Required sensor labor matching guide

05 - Hood

Fail

Major R/I and refinishing operations present; masks, cavity wax, seam sealer, and key prep/protection items missing.

Remove/Replace HoodOEM R&R with correct labor and refinish time.
Req: 1.9 R&R, 3.8 refinishEst: 1.9, 3.8
Add for Clear CoatIncluded as separate refinish operation.
Req: As needed per paint opsEst: 1.5
Add for Underside/Second Color'Add for Underside(Complete)' included.
Req: 1.0-2.0Est: 1.6
Mask hood inner edgesNo lines for masking edges/priming, significant for aluminum/OEM hood processes.
Req: 0.3Est: missing
Cavity wax/seam sealer as neededNo cavity wax or sealer/adhesion lines for new aluminum hood replacement.
Req: 1.0Est: missing
R&I hood insulationNo line for this required operation in aluminum hood replacement.
Req: 0.3Est: missing

Missing Line Items

R&I Hood insulation
Cavity wax
Seam sealer
Mask inner edges
Wrap/store & protect parts

10 - Fender

Warning

Fender R&R and liner R&I included, but missing several common protection and adhesive removal items.

Remove/Replace Fender (both sides)Both sides R&R/LKQ, labor matches estimate guide.
Req: 2.6 labor, 2.2 refinishEst: 2.6, 2.2
Remove/Replace Fender liner (both sides)Present for both sides at guide minimum.
Req: 0.8 eaEst: 0.3 ea
Clean and remove excessive adhesiveNo line for this operation, usually needed when swapping emblems and moldings.
Req: $2.30, 2.0Est: missing
Wrap/store and protect R&I itemsNo protection operation for moldings/liners/flares.
Req: $3.00, 0.2Est: missing

Missing Line Items

Clean and remove excessive adhesive
Wrap-store and protect R&I items
Replace liner/fastener if damaged
Mask fender jambs

15/25 - Coresupport/Apron/Upper Rail

Fail

Coresupport replaced/overhauled but several required weld, prep, corrosion, and cavity wax operations omitted.

Remove/Replace Radiator support (aluminum)Operation and parts present.
Req: R&I/R&R presentEst: included
Setup and measure unibodyIncluded as frame operation.
Req: Setup & measure requiredEst: 3.0
Access/Pre-pull/Structural pullRough pull and sheetmetal pull both listed.
Req: Pulls requiredEst: 2+
Replace caulking & seam sealerNo seam sealer/caulking lines listed.
Req: 1.0-2.0Est: missing
Cavity wax applicationNo cavity wax operation (critical for welded/jointed rails and core/structural parts).
Req: 0.5Est: missing
Weld-thru primer for welded/jointed structureNo weld-thru primer item anywhere for these operations.
Req: 0.3Est: missing
Welder test and set upMissing from all welded structure work.
Req: min 0.2Est: missing
Mask for primer applicationNot present, required on major welded/repaired structure.
Req: 0.3Est: missing

Missing Line Items

Replace caulking & seam sealer
Cavity wax
Weld-thru primer
Welder test & setup
Mask for primer application

20/30 - Cooling / Mechanical

Pass

Mechanical A/C and radiator R&I/R&R is correct; fluid top-off and checks not itemized.

R&I and recharge A/CEvacuate, recharge, recover refrigerant all included.
Req: 1.4MEst: 1.4, 0.4
R&I RadiatorPresent with minimum labor.
Req: 1.0MEst: 2.9 body

45/50 - Pillars & Rocker (Pinch Weld)

Fail

Rocker pinch weld repair present, but missing mandatory weld/corrosion protection and masking items for structural repair.

Rocker Pinch Weld Clamp RepairLine present at 1.0 labor (acceptable).
Req: 1.0Est: 1.0
Refinish rocker pinch weldItem present.
Req: 1.0Est: 1.0
Weld-thru primerNot itemized.
Req: 0.3Est: missing
Cavity waxNot itemized.
Req: 0.3-0.5Est: missing
Mask for weld-through primer or structure paintNot itemized.
Req: 0.5-1.0Est: missing

Missing Line Items

Weld-thru primer
Cavity wax
Mask/primer

55 - Door

Pass

Blending and major R&I for door shells, hardware removal, and trim all present for both sides.

Blend RT/LT Door shellPresent at correct labor unit.
Req: 1.1Est: 1.1
Remove/Install all associated trim (belts/mirrors/handles/panels)All shown in estimate with labor.
Req: listed, min. 0.2 eachEst: 0.2 - 0.7

60 - Roof / Headliner

Warning

Major headliner R&R present, but essential protection, masking or wrap/store operations missing.

Remove/Replace HeadlinerLine present with 5.3 labor.
Req: 5.0+Est: 5.3
Wrap-store and protect R&I itemsNot included on this or adjacent sections.
Req: as neededEst: missing

Missing Line Items

Wrap-store and protect R&I items

40 - SRS/Seat Belts

Pass

All airbag and SRS disable/enable/diagnosis lines are present with proper labor.

R&I/Replace Air bags and SRS system disable/diagnosisAll required airbag/SRS items with correct labor units.
Req: 0.5-1.2Est: all listed, 0.3-1.1

110/115 - Paint Prep & Refinish

Fail

Some paint prep steps present, but major industry-required masking/protection/corrosion items missing, especially for welded and new structural panels.

Color Tint & TestPresent.
Req: 0.5-2.0Est: 0.5
Mask Engine, Jambs, Interior, Exterior (bagging)Multiple masking steps itemized with labor.
Req: All included, min. 0.3-0.5 eaEst: all present
Corrosion protection (Refinish)No separate corrosion protection after major welded new parts.
Req: 1.0Est: missing
Hazardous waste removal/disposalPresent as single line.
Req: 1.0-1.1Est: 1.0

Missing Line Items

Restoration corrosion protection (after welded section)
Paint film mil thickness, cut to spec

180 - ADAS Functionality/Diagnostics

Pass

Both pre-repair and post-repair scans are present with associated labor.

Pre-repair scanPresent as stand-alone line (0.5M).
Req: 0.5MEst: 0.5
Post-repair scanPresent as stand-alone line (0.5M).
Req: 0.5MEst: 0.5